RODYN
RODYN
Papers Illustrating the Results of DyRoBeS Software Analyses
____________________________________________________________________________
Click any of the following papers to download a PDF version
Excerpt from DyRoBeS Version 10 Manual, W. J. Chen.
"Dynamic Analysis of a Turbocharger in Floating Bushing Bearings," E. J. Gunter and Chen, W. J., ISCORMA-3, Cleveland, Ohio.
"Application of Rotor Dynamic Analysis for Evaluation of Synchronous Speed Instability and Amplitude Hysteresis at 2nd Mode for a Generator Rotor in a High-Speed Balancing Facility,", M. M. L'vov and Gunter. E. J. , ISCORMA-3, Cleveland, Ohio, 2005.
"Nonlinear Whirl response of a High-Speed Seal Test Rotor with Marginal and Extended Squeeze-Film Dampers," M. P. Proctor and Gunter, E. J., ISCORMA-3, Cleveland, Ohio, 2005.
"Dynamic Analysis of An 1150 MW Turbine-Generator, " E. J. Gunter and Chen, W. J., ASME Proceedings of PW R2005, Chicago, IL, 2005.
"Dynamic Analysis of a 7 Stage Pump," Personal notes by E. J. Gunter, 2005.
"Evaluating and
Correcting Subsynchronous Vibration in Vertical Pumps,"
Malcolm E. Leader, P.E., Conner, Kelly J., and Lucas, Jamie D., Proceedings of
Vibration Institute Annual Meeting, 2010.
"Hydrodynamic Journal Bearing
Characteristics for SONGS 1150 MW Turbine-Generator," E. J., Gunter,
and Fang, Z., RODYN Vibration Analysis paper, December 1993.
"Transient Rotor Drop
Evaluation of AMB Machinery, " R. G. Kirk, Gunter, E. J., and Chen, W.
J., NEDO ISO Conference, 2004.
"Design and Application of Squeeze Film
Dampers for Turbomachinery Stabilization," Edgar J., Gunter, Jr.,
Proceedings of the Fourth Turbomachinery Symposium.
"Practical Implementation of
Torsional Analysis and Field Measurement," Malcolm E. Leader, P.E., and Kelm, Ray
D., P.E.
"Design of Nonlinear
Squeeze-Film Dampers for Aircraft Engines," E. J. Gunter, Journal of
Lubrication Technology, Vol. 99, No. 1, January 1977.
"Time Transient Analysis and
Non-Linear Rotordynamics," Malcolm E. Leader, P.E.
"Field Balancing 70 MW Gas
Turbine Generators," E. J. Gunter.
"Analysis of a Pocket Thrust Bearing Using DyRoBeS BePerf Version 12," W. J. Chen.
"Understanding Amplitude and Phase in Rotating Machinery, " E. J. Gunter, Vibration Institute 33rd Annual Meeting, Harrisburg, PA, 2009.
"Lund's Contribution to Rotor Stability: The Indispensable and Fundamental Basis of Modern Compressor Design," Edgar J., Gunter, Proceedings of DETC'01, 2001 ASME Design Engineering Technical Conferences, September 9-12, 2001, Pittsburgh, Pennsylvania.
"Critical Speed Analysis
of Offset Jeffcott Rotor Using English and Metric Units," E. J., Gunter,
Ph.D.,
RODYN Vibration Analysis, Inc., paper, February 2004.
"Effect of
Residual Shaft Bow on Unbalance Response and Balancing of a Single Mass Flexible
Rotor," J. C. Nicholas, Gunter, E. J., and Allaire, P. E.,
Reprint from Engineering for Power Vol. 98, No. 2, April 1976.
"Experimental-Theoretical Comparison of Instability Onset Speeds for a Three Mass Rotor Supported by Step Journal Bearings, J. C. Nicholas, Barrett, L. E., and Gunter, M. E., ASME Paper No. 79-DET-56.
"Forward and Backward Critical Speeds and Forced Response of an Overhung Rotor With Assymetrical Bearing Supports," E. J. Gunter, Ph.D., Director, Rotordynamics Laboratory, Department of Mechanical and Aerospace Engineering, University of Virginia, December 1993.
"Influence of Unbalance on the Nonlinear Dynamical Response of Flexible Rotor-Bearing Systems," E. J. Gunter, Humphris, R. R., and Springer, H., Proceedings of the Applied Mechanics, Bioengineering, and Fluids Engineering Conference, Houston, TX, June 20-22, 1983.
"Rotor Drop Transient Analysis of AMB Machinery," R. G. Kirk, Gunter, E. J., and Chen, W. J., DETC2005-84272, Proceedings of the IDETC/CIE 2005, ASME 2005 International Design Engineering Technical Conferences & Computers Information in Engineering Conference, September 24-28, 2005, Long Beach, CA.
"Experimental and Analytical Investigation of a Main Coolant Pump," E. J., Gunter, O'Brien, J. T., and O'Brien, J. T., Jr., Sound and Vibration Magazine, May 1993.